Top

Aluminium Wire

CHEMICAL COMPOSITION EN 573-3

Designation of the material Chemical Composition Other elements Min. Al
Classification of symbols Numerical classification Si Fe Cu Mn Mg Cr Zn Ti Notes Each Total
EN AW-1050A EN AW-Al 99.5 0.25 0.40 0.05 0.05 0.05 - 0.07 0.05       99.5
EN AW-2017A EN AW-Al CuMgSi (A) 0.20 - 0.8 0.70 3.5 - 4.5 0.40 - 1.0 0.40 - 1.0 0.10 0.25 0.25 (Ti+Zr)   0.05 0.15 Remainder
EN AW-2024 EN AW-Al Cu4MgSi 0.50 0.50 3.8 - 4.9 0.30 - 0.9 1.2 - 1.8 0.10 0.25 0.15        
EN AW-5052 EN AW-Al Cu4Mg1 0.25 0.40 0.10 0.10 2.2 - 2.8 0.15 - 0.35 0.15 - 0.35 0.10   0.05 0.15 Remainder
EN AW-5754 EN AW-Al Mg3 0.40 0.40 0.10 0.50 2.6 - 3.6 0.30 0.20 0.15 0.10 - 0.6 Mn + Cr 0.05 0.15 Remainder
EM AW-6082 EN AW-Al Si1MgMn 0.7 - 1.3 0.50 0.10 0.40 - 1.00 0.6 - 1.2 0.25 0.20 0.10   0.05 0.15 Remainder
EN AW-7075 EN AW-Al Zn5.5MgCu 0.40 0.50 1.2 - 2.0 0.30 2.1 - 2.9 0.18 - 0.28 5.1 - 6.1 0.2 - 0.25 (Zr+Ti)   0.05 0.15 Remainder
 
  Approximate international equivalents
Classification of symbols Numerical classification US (AISI) Japan (JIS) China (GB)
EN AW-1050A EN AW-Al 99.5            
EN AW-2017A EN AW-Al CuMgSi (A)            
EN AW-2024 EN AW-Al Cu4MgSi            
EN AW-5052 EN AW-Al Cu4Mg1            
EN AW-5754 EN AW-Al Mg3            
EN AW-6082 EN AW-Al Si1MgMn            
EN AW-7075 EN AW-Al Zn5.5MgCu            
 

MECHANICAL PROPERTIES EN 1301-2
 

1000 SERIES (Al)

Designation of the material Metallurgical condition Diameter d up to & including (mm) Tensile strength Yield strength Rp0.2 Elongation
Rm
MPA MPa A100 mm
min. max. typical (typical %)
  O 20 - 95 - 35
EN AW-1050A [Al 99.5] H14 18 100 - 95 5
  H16 15 120 - 115 3
  H18 10 140 - 135 3

 

2000 SERIES (Al Cu)

Designation of the material Metallurgical condition Diameter d up to & including (mm) Tensile strength Yield strength Rp0.2 Elongation
Rm
MPA MPa A100 mm
min. max. typical (typical %)
  H13 18 210 300 190 5
EN AW-2017A [Al Cu4MgSi(A)] T4 18 380 - 255 18
  H18 10 315 - - -
  H13 18 230 300 200 5
EN AW-2024 [Al Cu4Mg1] T4 18 420 - 315 18
  H18 10 320 - - -

 

5000 SERIES (Al Mn)

Designation of the material Metallurgical condition Diameter d up to & including (mm) Tensile strength Yield strength Rp0.2 Elongation
Rm
MPA MPa A100 mm
min. max. typical (typical %)
  O 20 - 225 100 15
  H14 18 225 275 225 4
EN AW-5052 [Al Mg2.5] H18 10 275 - 275 3
  H32 18 190 240 145 11
  H34 15 215 265 195 8
  H38 10 260 - 245 5
  O 20 - 250 110 16
  H12 18 230 280 200 6
  H14 18 255 305 250 3
EN AW-5754 [Al Mg3] H18 10 305 - 300 2
  H32 18 220 270 160 11
  H34 15 245 295 210 8
  H38 10 290 - 260 4

 

 

6000 SERIES (Al MgSi) 

Designation of the material Metallurgical condition Diameter d up to & including (mm) Tensile strength Yield strength Rp0.2 Elongation
Rm
MPA MPa A100 mm
min. max. typical (typical %)
  H13 ≤ 18 165 225 130 4
  H18 ≤ 10 220 - 200 2
  T39 ≥ 6 310 - - -
EN AW-6082 [Al Si1MgMn] T39 < 6 360 - - -
  T4 ≤ 20 205 285 135 13
  T6 ≤ 20 300 - 270 10
  T89 < 6 340 - - -

 

7000 SERIES (Al Zn)

Designation of the material Metallurgical condition Diameter d up to & including (mm) Tensile strength Yield strength Rp0.2 Elongation
Rm
MPA MPa A100 mm
min. max. typical (typical %)
  O 20 - 275 110 13
EN AW-7075 [Al Zn5.5MgCu] H13 18 230 310 230 2.5
  H18 10 285 - 260 2
  T6 20 510 - 485 10
 
  • To be determined under a commercial agreement when placing the order or requesting the quote.

DIMENSIONAL TOLERANCES ACCORDING TO STANDARD UNE-EN 1301-3

 

DIMENSIONAL TOLERANCES ROUND WIRE

Specified diameter Tolerance
From To (inclusive) General Application
- 1 ± 0.02
1 3 ± 0.03
3 6 ± 0.04
6 10 ± 0.05
10 15 ± 0.07
15 20 ± 0.11

 

 

DIMENSIONAL TOLERANCES RECTANGULAR WIRE

Width or thickness Tolerance
From To Thickness Width
- 1 ± 0.03 ± 0.04
1 3 ± 0.04 ± 0.05
3 6 ± 0.05 ± 0.07
6 10 ± 0.07 ± 0.1
10 15 ± 0.1 ± 0.14
15 20 ± 0.14 ± 0.18

 

STANDARD LENGTH TOLERANCES

NOMINAL LENGTH TOLERANCE
L < = 1000 mm. +/- 1 mm.
1000 < L < = 4000 - 0mm. / +3 mm.
* The data contained in this catalogue are for information purposes only and are not under any circumstances, contractual supply conditions. Errors and omissions excepted.
Product search engineStrip, wire, wire rope.