Top

Low-Carbon Steel Wire

CHEMICAL ANALYSIS (HEAT ANALYSIS) EN 10016-2

Type of steel Heat analysis
Designation
Symbolic Numerical % C % Si % Mn Max. % P Max. % S Max. % Cr Max. % Ni Max. % Mo Max. Cu Max. % Al
C4D 1.0300 ≤ 0.06 ≤ 0.30 0.30 - 0.60 0.035 0.035 0.20 0.25 0.05 0.30 0.01
C7D 1.0313 0.05 - 0.09 ≤ 0.30 0.30 - 0.60 0.035 0.035 0.20 0.25 0.05 0.30 0.01
C9D 1.0304 ≤ 0.10 ≤ 0.30 ≤ 0.60 0.035 0.035 0.25 0.25 0.08 0.30 -
C15D 1.0413 0.12 - 0.17 ≤ 0.30 0.30 - 0.60 0.035 0.035 0.20 0.25 0.05 0.30 0.01
Designation

US

JAPAN CHINA
Symbolic Numerical AISI/SAE JIS GB
C4D 1.0300      
C7D 1.0313 1008    
C9D 1.0304      
C15D 1.0413      
 

Without coating:

Material Range Approx. Rm (N/mm2)
Annealed - 330 - 400
N/A - under agreement
Hard Drawn (Grey) 0.8 -1.5 750-1100
1.51 - 3.00 650-950
3.01 - 4.50 600-850
>4.51 500-700

 

With coating:

Material Range Approx. Rm (N/mm2)
Annealed Galvanised - 400 - 450
Hard Galvanised (Grey) - 700 - 850
 
We can supply the following types of coatings:
Galvanised - Reinforced galvanised - ZA - Reinforced ZA

 

Coating density EN 10244

  Coating density EN 10244
A B C
Diameter d mm g/m2 g/m2 g/m2
0.15 ≤ d < 0.20 - 15 -
0.20 ≤ d < 0.25 30 20 20
0.25 ≤ d < 0.32 45 30 25
0.32 ≤ d < 0.40 60 30 25
0.40 ≤ d < 0.50 85 40 30
0.50 ≤ d < 0.60 100 50 35
0.60 ≤ d < 0.70 115 60 40
0.70 ≤ d < 0.80 130 60 45
0.80 ≤ d < 0.90 145 70 50
0.90 ≤ d < 1.00 155 70 55
1.00 ≤ d < 1.20 165 80 60
1.20 ≤ d < 1.40 180 90 65
1.40 ≤ d < 1.65 195 100 70
1.65 ≤ d < 1.85 205 100 75
1.85 ≤ d < 2.15 215 115 80
2.15 ≤ d < 2.50 230 125 85
2.50 ≤ d < 2.80 245 125 95
2.80 ≤ d < 3.20 255 135 100
3.20 ≤ d < 3.80 265 135 105
3.80 ≤ d < 4.40 275 135 110
4.40 ≤ d < 5.20 280 150 110
5.20 ≤ d < 8.20 290 - 110
8.20 ≤ d < 10.00 300 - 110

Guidance information.
Note: Can be supplied in copper plating

 

TOLERANCES DIN 177

Nominal diameter tolerances
Nominal diameter d mm Grey, Galvanised, Electro-zinc plated, Z/A
0.10 ≤ d < 0.25 ± 0.01
0.25 ≤ d < 0.40 ± 0.015
0.40 ≤ d < 0.63 ± 0.02
0.63 ≤ d < 1.00 ± 0.03
1.00 ≤ d < 1.60 ± 0.04
1.60 ≤ d < 2.50 ± 0.06
2.50 ≤ d < 4.00 ± 0.08
4.00 ≤ d < 6.30 ± 0.10
6.30 ≤ d < 10.00 ± 0.15
10.00 ≤ d < 16.00 ± 0.20
16.00 ≤ d ≤ 20.00 ± 0.25

Note: Can be supplied in copper plating

 

 

WHEN SUPPLIED IN RODS. Straightened wire:

Nominal diameter d mm Length tolerance mm.
Minimum length Maximum length
0.65 ≤ d < 0.80 50 2000
0.80 ≤ d < 2.01 30 2000
2.01 ≤ d < 3.01 30 4000
3.01 ≤ d < 4.35 30 4000
4.35 ≤ d < 6.01 30 4350
6.01 ≤ d < 10.50 250 4350

Approximate data for information purposes

 

STANDARD LENGTH TOLERANCES

NOMINAL LENGTH TOLERANCE
L < = 1000 mm. +/- 1 mm.
1000 < L < = 4000 - 0mm. / +3 mm.
* The data contained in this catalogue are for information purposes only and are not under any circumstances, contractual supply conditions. Errors and omissions excepted.
Product search engineStrip, wire and wire rope.