Aluminium Wire

MECHANICAL PROPERTIES EN 1301-2

1000 SERIES (Al)

Designation of the material	Metallurgical condition	Diameter d up to & including (mm)	Tensile strength		Yield strength Rp_0.2	Elongation
			R_m		Yield strength Rp_0.2	Elongation
			MPA		MPa	A_{100 mm}
			min.	max.	typical	(typical %)
EN AW-1050A [Al 99.5]	O	20	–	95	–	35
	H14	18	100	–	95	5
	H16	15	120	–	115	3
	H18	10	140	–	135	3

2000 SERIES (AlCu)

Designation of the material	Metallurgical condition	Diameter d up to & including (mm)	Tensile strength		Yield strength Rp_0.2	Elongation
			R_m		Yield strength Rp_0.2	Elongation
			MPA		MPa	A_{100 mm}
			min.	max.	typical	(typical %)
EN AW-2017A [Al Cu4MgSi(A)]	H13	18	210	300	190	5
	T4	18	380	–	255	18
	H18	10	315	–	–	–
EN AW-2024 [Al Cu4Mg1]	H13	18	230	300	200	5
	T4	18	420	–	315	18
	H18	10	320	–	–	–

5000 SERIES (AlMn)

Designation of the material	Metallurgical condition	Diameter d up to & including (mm)	Tensile strength		Yield strength Rp_0.2	Elongation
			R_m		Yield strength Rp_0.2	Elongation
			MPA		MPa	A_{100 mm}
			min.	max.	typical	(typical %)
EN AW-5052 [Al Mg2.5]	O	20	–	225	100	15
	H14	18	225	275	225	4
	H18	10	275	–	275	3
	H32	18	190	240	145	11
	H34	15	215	265	195	8
	H38	10	260	–	245	5
EN AW-5754 [Al Mg3]	O	20	–	250	110	16
	H12	18	230	280	200	6
	H14	18	255	305	250	3
	H18	10	305	–	300	2
	H32	18	220	270	160	11
	H34	15	245	295	210	8
	H38	10	290	–	260	4

6000 SERIES (AlMgSi)

Designation of the material	Metallurgical condition	Diameter d up to & including (mm)	Tensile strength		Yield strength Rp_0.2	Elongation
			R_m		Yield strength Rp_0.2	Elongation
			MPA		MPa	A_{100 mm}
			min.	max.	typical	(typical %)
EN AW-6082 [Al Si1MgMn]	H13	≤ 18	165	225	130	4
	H18	≤ 10	220	–	200	2
	T39	≥ 6	310	–	–	–
	T39	< 6	360	–	–	–
	T4	≤ 20	205	285	135	13
	T6	≤ 20	300	–	270	10
	T89	< 6	340	–	–	–

7000 SERIES (AlZn)

Designation of the material	Metallurgical condition	Diameter d up to & including (mm)	Tensile strength		Yield strength Rp_0.2	Elongation
			R_m		Yield strength Rp_0.2	Elongation
			MPA		MPa	A_{100 mm}
			min.	max.	typical	(typical %)
EN AW-7075 [Al Zn5.5MgCu]	O	20	–	275	110	13
	H13	18	230	310	230	2.5
	H18	10	285	–	260	2
	T6	20	510	–	485	10

CHEMICAL COMPOSITION EN 573-3

Designation of the material		Chemical Composition									Other elements		Min. Al
Classification of symbols	Numerical classification	Si	Fe	Cu	Mn	Mg	Cr	Zn	Ti	Notes	Each	Total	Min. Al
EN AW-1050A	EN AW-Al 99.5	0.25	0.40	0.05	0.05	0.05	–	0.07	0.05				99.5
EN AW-2017A	EN AW-Al CuMgSi (A)	0.20 – 0.8	0.70	3.5 – 4.5	0.40 – 1.0	0.40 – 1.0	0.10	0.25	0.25 (Ti+Zr)		0.05	0.15	Remainder
EN AW-2024	EN AW-Al Cu4MgSi	0.50	0.50	3.8 – 4.9	0.30 – 0.9	1.2 – 1.8	0.10	0.25	0.15
EN AW-5052	EN AW-Al Cu4Mg1	0.25	0.40	0.10	0.10	2.2 – 2.8	0.15 – 0.35	0.15 – 0.35	0.10		0.05	0.15	Remainder
EN AW-5754	EN AW-Al Mg3	0.40	0.40	0.10	0.50	2.6 – 3.6	0.30	0.20	0.15	0.10 – 0.6 Mn + Cr	0.05	0.15	Remainder
EM AW-6082	EN AW-Al Si1MgMn	0.7 – 1.3	0.50	0.10	0.40 – 1.00	0.6 – 1.2	0.25	0.20	0.10		0.05	0.15	Remainder
EN AW-7075	EN AW-Al Zn5.5MgCu	0.40	0.50	1.2 – 2.0	0.30	2.1 – 2.9	0.18 – 0.28	5.1 – 6.1	0.2 – 0.25 (Zr+Ti)		0.05	0.15	Remainder

DIMENSIONAL TOLERANCES ACCORDING TO STANDARD UNE-EN 1301-3

DIMENSIONAL TOLERANCES ROUND WIRE

Specified diameter		Tolerance
From	To (inclusive)	General Application
–	1	± 0.02
1	3	± 0.03
3	6	± 0.04
6	10	± 0.05
10	15	± 0.07
15	20	± 0.11

DIMENSIONAL TOLERANCES RECTANGULAR WIRE

Width or thickness		Tolerance
From	To	Thickness	Width
–	1	± 0.03	± 0.04
1	3	± 0.04	± 0.05
3	6	± 0.05	± 0.07
6	10	± 0.07	± 0.1
10	15	± 0.1	± 0.14
15	20	± 0.14	± 0.18

STANDARD LENGTH TOLERANCES

NOMINAL LENGTH	TOLERANCE
L < = 1000 mm.	+/- 1 mm.
1000 < L < = 4000	– 0mm. / +3 mm.

To be determined under a commercial agreement when placing the order or requesting the quote.

Classification of symbols	Numerical classification	US (AISI)
		Approximate international equivalents
EN AW-1050A	EN AW-Al 99.5
EN AW-2017A	EN AW-Al CuMgSi (A)
EN AW-2024	EN AW-Al Cu4MgSi
EN AW-5052	EN AW-Al Cu4Mg1
EN AW-5754	EN AW-Al Mg3
EN AW-6082	EN AW-Al Si1MgMn
EN AW-7075	EN AW-Al Zn5.5MgCu

ALUMINUM WIRE: CORROSION AND FATIGUE RESISTANCE

CHEMICAL COMPOSITION AND MECHANICAL CHARACTERISTICS

At VINCO we are specialists in the supply of wires focused on sectors such as automotive and electronics, agri-food, spring and spring and general uses. We have a wide range of wires -round, square and flat- including diameters from 0.10 mm to 22 mm so that you can choose the one that best suits your needs. In addition, we have ISO 9001 and ISO 14001 certifications that ensure quality and commitment to the environment throughout our production process and product delivery.

In our catalog you will find a wide variety of chemical compositions of aluminum wire based on the European Standard EN 573-3 which lists the chemical composition. The mechanical characteristics are detailed according to EN 1301-2 which deals with aluminum and aluminum alloys. In this sense, it is important to differentiate between the different aluminum alloys since, depending on each of them, the wire will have certain properties: the 1000 series (Al) is characterized by excellent corrosion resistance in a wide variety of environments; the 2000 series (Al Cu) is known for its good mechanical strength in high temperature applications; the 5000 series (Al Mn) has good corrosion resistance and weldability; the 6000 series (Al MgSi) has high weldability; and the 7000 series (Al Zn) has high mechanical strength.

SUPPLY AND PACKAGING OPTIONS

When ordering any chemical composition for aluminum wire, we offer you the possibility to choose the packaging format taking into account the maximum weight in kilograms. Each of them is listed in the table below:

Packaging format	Maximum weight in kg
Roll	500
Coil Z	800
Plastic reel DIN 160	7
Rods	–

We offer different supply options at the customer’s choice for the type of palletizing, reel axis orientation and material protection elements to ensure that the product arrives in perfect conditions: lid, paper or VCI anti-humidity plastic, phytosanitary packaging, maritime packaging and anti-humidity bags.

Aluminium Wire

Mechanical properties

Chemical composition

Tolerances

Finishes

Equivalents

General information

MECHANICAL PROPERTIES EN 1301-2

CHEMICAL COMPOSITION EN 573-3

DIMENSIONAL TOLERANCES ACCORDING TO STANDARD UNE-EN 1301-3

ALUMINUM WIRE: CORROSION AND FATIGUE RESISTANCE